Digital Electronics and Computer Organisation MCQs [set-1]
Digital Electronics and Computer Organisation MCQs [set-1]
1. Any number with an exponent of zero is equal to:
A. zero
B. one
C. that number
D. ten
Answer: B
2. In the decimal numbering system, what is the MSD?
A. the middle digit of a stream of numbers
B. the digit to the right of the decimal point
C. the last digit on the right
D. the digit with the most weight
Answer: D
3. Which of the following statements does NOT describe an advantage of digital technology?
A. the values may vary over a continuous range.
B. the circuits are less affected by noise.
C. the operation can be programmed.
D. information storage is easy.
Answer: A
4. The generic array logic (GAL) device is ________.
A. one-time programmable
B. reprogrammable
C. a cmos device
D. reprogrammable and a cmos device
Answer: B
5. The range of voltages between VL(max) and VH(min) are ________.
A. unknown
B. unnecessary
C. unacceptable
D. between 2 v and 5 v
Answer: C
6. What is a digital-to-analog converter?
A. it takes the digital information from an audio cd and converts it to a usable form.
B. it allows the use of cheaper analog techniques, which are always simpler.
C. it stores digital data on a hard drive.
D. it converts direct current to alternating current.
Answer: A
7. What are the symbols used to represent digits in the binary number system?
A. 0,1
B. 0,1,2
C. 0 through 8
D. 1,2
Answer: A
8. A full subtracter circuit requires ________.
A. two inputs and two outputs
B. two inputs and three outputs
C. three inputs and one output
D. three inputs and two outputs
Answer: D
9. The output of an AND gate is LOW ________.
A. all the time
B. when any input is low
C. when any input is high
D. when all inputs are high
Answer: B
10. Give the decimal value of binary 10010.
A. 610
B. 910
C. 1810
D. 2010
Answer: C
11. Parallel format means that:
A. each digital signal has its own conductor.
B. several digital signals are sent on each conductor.
C. both binary and hexadecimal can be used.
D. no clock is needed.
Answer: A
12. A decoder converts ________.
A. noncoded information into coded form
B. coded information into noncoded form
C. highs to lows
D. lows to highs
Answer: B
13. A DAC changes ________.
A. an analog signal into digital data
B. digital data into an analog signal
C. digital data into an amplified signal
D. none of the above
Answer: B
14. The output of a NOT gate is HIGH when ________.
A. the input is low
B. the input is high
C. the input changes from low to high
D. voltage is removed from the gate
Answer: A
15. The output of an OR gate is LOW when ________.
A. all inputs are low
B. any input is low
C. any input is high
D. all inputs are high
Answer: A
16. Which of the following is not an analog device?
A. thermocouple
B. current flow in a circuit
C. light switch
D. audio microphone
Answer: C
17. A demultiplexer has ________.
A. one data input and a number of selection inputs, and they have several outputs
B. one input and one output
C. several inputs and several outputs
D. several inputs and one output
Answer: A
18. A flip-flop has ________.
A. one stable state
B. no stable states
C. two stable states
D. none of the above
Answer: C
19. Digital signals transmitted on a single conductor (and a ground) must be transmitted in:
A. slow speed.
B. parallel.
C. analog.
D. serial.
Answer: D
20. In a certain digital waveform, the period is four times the pulse width. The duty cycle is ________.
A. 0%
B. 25%
C. 50%
D. 100%
Answer: B
21. Select the statement that best describes the parity method of error detection:
A. parity checking is best suited for detecting double-bit errors that occur during the transmission of codes from one location to another.
B. parity checking is not suitable for detecting single-bit errors in transmitted codes.
C. parity checking is best suited for detecting single-bit errors in transmitted codes.
D. parity checking is capable of detecting and correcting errors in transmitted codes.
Answer: C
22. A logic circuit that provides a HIGH output for both inputs HIGH or both inputs LOW is a(n):
A. ex-nor gate
B. or gate
C. ex-or gate
D. nand gate
Answer: A
23. A logic circuit that provides a HIGH output if one input or the other input, but not both, is HIGH, is a(n):
A. ex-nor gate
B. or gate
C. ex-or gate
D. nand gate
Answer: C
24. Identify the type of gate below from the equation
A. ex-nor gate
B. or gate
C. ex-or gate
D. nand gate
Answer: C
25. Parity systems are defined as either________ or ________ and will add an extra ________ tothe digital information being transmitted.
A. positive, negative, byte
B. odd, even, bit
C. upper, lower, digit
D. on, off, decimal
Answer: B
Click For Set - 2👇
Post a Comment